| Chapter | Description | DurationHours | DurationMinutes |
| Introduction to Trade with Safety | Induction TrainingImportance of Safety (Theory) | 10 | 0 |
| Introduction to Trade with Safety | Institute VisitIntroduction to the machines used by a fitterObservation of jobs done by the traineesImportance of safety and Personal Protective Equipments (Practical) | 20 | 0 |
| Introduction to Trade with Safety | Institute VisitIntroduction to the machines used by a fitterObservation of jobs done by the traineesImportance of safety and Personal Protective Equipments (Practical) | 8 | 0 |
| Introduction to Trade with Safety | Extra Circular Activities | 4 | 0 |
| Fitter Tools | Linear Measurement and it unitsMeasuring Instrumentsdividers, calipers,hermaphrodite, calipers,hermaphrodite, center punch,dot punch dot punch, theirdescription and uses ofdifferent types of hammers,description, use and care of‘v’ Blocks, marking off table | 4 | 0 |
| Fitter Tools | Introduction to Engineering Drawing | 2 | 0 |
| Fitter Tools | Property and use of Cast Iron and Wrought Iron | 2 | 0 |
| Fitter Tools | Social Studies | 2 | 0 |
| Fitter Tools | Marking out linesgripping suitable invice jaws, hacksawing to givendimension sawingdifferent types ofmetals of differenttypes of metals ofdifferent sections. | 20 | 0 |
| Fitter Tools | Marking out linesgripping suitable invice jaws, hacksawing to givendimension sawingdifferent types ofmetals of differenttypes of metals ofdifferent sections. | 8 | 0 |
| Fitter Tools | Spoken English - Alphabets | 2 | 0 |
| Fitter Tools | Physical Training | 2 | 0 |
| Fitter Tools | TT:Bench vice construction,types, uses care andmaintenance, vice clamps,hacksaw frames and bladesspecification description,types and their uses, methodof using hacksaws. (Theory) | 4 | 0 |
| Fitter Tools | ED:Types of lines their meaning andapplication asper IS-696 | 2 | 0 |
| Fitter Tools | W/SC : Arithmetic:Fundamentaloperations,addition,subtraction.Multiplication,division decimals number. | 2 | 0 |
| Fitter Tools | TP:Bench vice construction,types, uses care andmaintenance, vice clamps,hacksaw frames and bladesspecification description,types and their uses, methodof using hacksaws. | 20 | 0 |
| Fitter Tools | TP:Bench vice construction,types, uses care andmaintenance, vice clamps,hacksaw frames and bladesspecification description,types and their uses, methodof using hacksaws. | 8 | 0 |
| Fitter Tools | Social Studies | 2 | 0 |
| Fitter Tools | Soft Skills:Vowels and consonants | 2 | 0 |
| Fitter Tools | Physical Training | 2 | 0 |
| Fitter Tools | TT:Files specification,description, materials grads,cuts file elements uses,Measuring standards (English) | 4 | 0 |
| Fitter Tools | ED:Simple conventionalsymbols formaterial | 2 | 0 |
| Fitter Tools | W/SC:Properties and uses of plaincarbon steel and alloy steel. | 2 | 0 |
| Fitter Tools | TP:Filing practice,surface filingmarking off straightand parallel lines | 20 | 0 |
| Fitter Tools | TP:Filing practice,surface filingmarking off straightand parallel lines | 8 | 0 |
| Fitter Tools | Social Studies | 2 | 0 |
| Fitter Tools | Soft Skills :Things identification | 2 | 0 |
| Fitter Tools | Physical Exercise | 2 | 0 |
| Fitter Tools | TT: Marking off and lay out tools,dividers, scribing block, oddleg calipers, punchesdescription, classificationmaterial care and maintenance. | 4 | 0 |
| Fitter Tools | ED:Use or drawing instruments in the construction of Geometrical drawing angles.Triangles. | 2 | 0 |
| Fitter Tools | W/SC:Fraction and decimalsconversion fraction to decimal and vice versa. | 2 | 0 |
| Fitter Tools | TP: Marking off straight lines and arcs using scribing block and dividers chipping flat surfaces along amarked line. | 20 | 0 |
| Fitter Tools | TP: Marking off straight lines and arcs using scribing block and dividers chipping flat surfaces along amarked line. | 8 | 0 |
| Fitter Tools | Social studies | 2 | 0 |
| Fitter Tools | Soft Skills:Things identification | 2 | 0 |
| Fitter Tools | Physical Training | 2 | 0 |
| Fitter Tools | TT:Calipers types material constructional details, uses care and maintenance of cold chisels, materials, Types,cutting angles. | 4 | 0 |
| Fitter Tools | ED:Geometricalconstruction of rectangles,square, circles. | 2 | 0 |
| Fitter Tools | W/SC:Properties and uses of copper,zinc, lead, tin,aluminum | 2 | 0 |
| Fitter Tools | TP:Marking, filing,filing square, use oftri-square. | 20 | 0 |
| Fitter Tools | TP:Marking, filing,filing square, use oftri-square. | 8 | 0 |
| Fitter Tools | Social studies | 2 | 0 |
| Fitter Tools | Soft Skills:Understanding short messages | 2 | 0 |
| Fitter Tools | Physical Training | 2 | 0 |
| Markings | TT:Marking media marking blue Prussian blue-red lead, chalk and their special application description. Use, care and maintenance of scribing block. | 8 | 0 |
| Markings | ED: Geometricalconstruction ofpolygons and ellipse, parabolaand hyper-bola. | 4 | 0 |
| Markings | W/Sc:Composition,properties and uses of brass,solder, bearing,metal, timber,rubber, etc. | 4 | 0 |
| Markings | TP:Marking accordingto simple blue prints locating position of holes scribing lines on chalked surfaces with making tools finding centre of round bar with thehelp of “V” block and marking block.Joining St. line toand arc. | 20 | 0 |
| Markings | TP:Marking accordingto simple blue prints locating position of holes scribing lines on chalked surfaces with making tools finding centre of round bar with thehelp of “V” block and marking block.Joining St. line toand arc. | 20 | 0 |
| Markings | TP:Marking accordingto simple blue prints locating position of holes scribing lines on chalked surfaces with making tools finding centre of round bar with thehelp of “V” block and marking block.Joining St. line toand arc. | 16 | 0 |
| Markings | Social Studies | 4 | 0 |
| Markings | Soft Skills:Understanding short messages | 4 | 0 |
| Markings | Physical Training | 4 | 0 |
| Markings | TT: Surface plate and auxiliarymarking equipment, ‘v’ block,angle plates, parallel block,description types and uses,workshop surface plate theiruses accuracy, care andmaintenance. | 4 | 0 |
| Markings | ED: Geometricalconstruction of involutes, oval,and helix. | 2 | 0 |
| Markings | W/SC: System of units,British, metricand SI units forlength area,volume, capacity,weight time,angle, their conversions. | 2 | 0 |
| Markings | TT: Chipping chip slotsand oils grooves(Straight.) | 20 | 0 |
| Markings | TT: Chipping chip slotsand oils grooves(Straight.) | 8 | 0 |
| Markings | Social Studies | 2 | 0 |
| Markings | Soft Skills:Speaking and Listening Test | 2 | 0 |
| Markings | Physical Training | 2 | 0 |
| Files | TT: Types of files conveningtaper, needle care andmaintenance of files, various types of keys, allowable clearances and tapers; types,uses of key pullers. | 4 | 0 |
| Files | ED:Geometrical construction of involutes, oval,and helix. | 2 | 0 |
| Files | W/SC:Effect of alloying elements on the property of C.I.and steel. | 2 | 0 |
| Files | TP:Filing flat, square,and parallel to anaccuracy of 0.5mm. Chip curve along a line-markout, key ways atvarious angles andcut key ways. | 20 | 0 |
| Files | TP:Filing flat, square,and parallel to anaccuracy of 0.5mm. Chip curve along a line-markout, key ways atvarious angles andcut key ways. | 8 | 0 |
| Files | Social studies | 2 | 0 |
| Files | Soft Skills:Speaking and Listening Test | 2 | 0 |
| Files | Physical Training | 2 | 0 |
| Properties of Engineering | TT: Physical properties ofengineering metal : color,weight, structure,conductivity, magnetic,fusibility specific gravity,fusibility specific gravity.Mechanical properties:ductility, malleabilityhardness, brittleness,toughness, tenacity, elasticity. | 4 | 0 |
| Properties of Engineering | ED:Free hand sketching of st.lines, rectangles,circles, square,polygons,Ellipse, | 2 | 0 |
| Properties of Engineering | W/SC:Unit of temperature forceand related problem | 2 | 0 |
| Properties of Engineering | TP:File thin metal toa n accuracy of 0.5mm. chip chamfer,Grooves and slots. | 20 | 0 |
| Properties of Engineering | TP:File thin metal toa n accuracy of 0.5mm. chip chamfer,Grooves and slots. | 8 | 0 |
| Properties of Engineering | Social Studies | 2 | 0 |
| Properties of Engineering | Soft Skills:Noun and verb | 2 | 0 |
| Properties of Engineering | Physical Training | 2 | 0 |
| Properties of Engineering | TT: Physical properties ofengineering metal : color,weight, structure,conductivity, magnetic,fusibility specific gravity,fusibility specific gravity.Mechanical properties:ductility, malleabilityhardness, brittleness,toughness, tenacity, elasticity | 4 | 0 |
| Properties of Engineering | ED:Free hand sketching ofsimplegeometricalsolids cube,cone, prism,cylinder, spherepyramids. | 2 | 0 |
| Properties of Engineering | W/Sc:Mass, volume density, sp.Gravity andspecific weightS.I. M.K.S. andF.P.S. units offorce, weight etc.their conversionto related problems | 2 | 0 |
| Properties of Engineering | TP:Saw along a straight line curvedline, on differentsection of metal.Straight saw onthick section. M.Sangle and pipes | 20 | 0 |
| Properties of Engineering | TP:Saw along a straight line curvedline, on differentsection of metal.Straight saw onthick section. M.Sangle and pipes | 8 | 0 |
| Properties of Engineering | Social Studies | 2 | 0 |
| Properties of Engineering | Soft Skills:Noun and verb | 2 | 0 |
| Measurement tools | TT: Micrometer outside and inside principle constructional features, parts graduation reading, use and care.Micrometer depth gauge,parts, graduation, reading, use and care. | 4 | 0 |
| Measurement tools | ED: Standard printing style forletters and numbers as perIS:696 | 2 | 0 |
| Measurement tools | W/SC:Mass, volume,density, weight.S.I., M.K.S andF.P.S. units of force weight etc.their conversionto relatedproblems | 2 | 0 |
| Measurement tools | TP:File steps and finish with smooth file accuracy =0.25mm. File and sawon M.S. Square and pipe welds. | 20 | 0 |
| Measurement tools | TP:File steps and finish with smooth file accuracy =0.25mm. File and sawon M.S. Square and pipe welds. | 8 | 0 |
| Measurement tools | Social Studies | 2 | 0 |
| Measurement tools | Soft Skills:Tense | 2 | 0 |
| Measurement tools | TT:Vernier calipers, principle,construction, graduations,reading, use and care. Vernier bevel protractor, constructiongraduations, reading, use and care Dial Vernier Caliper. | 4 | 0 |
| Measurement tools | ED:Free hand practice of printing style force standard lettersand numbers. | 2 | 0 |
| Measurement tools | W/SC:Inertia, rest and motion velocity and acceleration. | 2 | 0 |
| Measurement tools | TP: File radius along amarked line (Convex andConcave) and match.Chip step and file. | 20 | 0 |
| Measurement tools | TP: File radius along amarked line (Convex andConcave) and match.Chip step and file. | 8 | 0 |
| Measurement tools | Social Studies | 2 | 0 |
| Measurement tools | Soft Skills:Tense | 2 | 0 |
| Holding Devices | TT: Drill holding devices:material, construction and their uses. Drill processes:Common type (bench type,pillar type) gang and multiple drilling machine. | 4 | 0 |
| Holding Devices | ED:Scales construction of plain scale.Representingfraction. | 2 | 0 |
| Holding Devices | W/SC:Concept of scalar and vector quantity with examples,Newton’s Law ofmotion. | 2 | 0 |
| Holding Devices | TP:Punch letter andnumber (letter number punch) Useof different punches. | 20 | 0 |
| Holding Devices | TP:Punch letter andnumber (letter number punch) Useof different punches. | 8 | 0 |
| Holding Devices | Social Studies | 2 | 0 |
| Holding Devices | Soft Skills:Tense | 2 | 0 |
| Holding Devices | TT:Safety precautions to be observed in a smith shop forge: Necessity, descriptionuses, fuel used for heating,bellows blowers description and uses. | 4 | 0 |
| Holding Devices | ED:Construction ofdiagonal scale. | 2 | 0 |
| Holding Devices | W/S:Revision andTest power and roots Factor, power base exponents number | 2 | 0 |
| Holding Devices | TP:Prepare forge. Fire for heating metals Forge a square rodfrom found stock.Judge the forging temperature ofvarious metals. | 20 | 0 |
| Holding Devices | TP:Prepare forge. Fire for heating metals Forge a square rodfrom found stock.Judge the forging temperature ofvarious metals. | 8 | 0 |
| Holding Devices | Social Studies | 2 | 0 |
| Holding Devices | Soft Skills: Tenses | 2 | 0 |
| Holding Devices | TT:Anvil and swage blocks,Description and uses Forging tools hammers band and sledge description and uses.Chisels, set hammers, flatters,hardier, fuller swage and uses. | 4 | 0 |
| Holding Devices | ED:dimensioning technique size and location dimension forparts, holesangles , taper,screw etc. as per IS : 696 | 2 | 0 |
| Holding Devices | W/SC:Multiplication and division of numbers | 2 | 0 |
| Holding Devices | TP:Forge M.S. bar to square Octagon and hexagon. | 20 | 0 |
| Holding Devices | TP:Forge M.S. bar to square Octagon and hexagon. | 8 | 0 |
| Holding Devices | Social Studies | 2 | 0 |
| Holding Devices | Soft Skills:Active and passive voice | 2 | 0 |
| Heat Treatment | TT:Heat treatment necessary various heat treatment methods such as normalizingannealing, hardening and tempering. Power hammerconstruction feature ,method of operating and uses. | 4 | 0 |
| Heat Treatment | ED:Pictorial drawings isometric drawings of simple geometrical solids. | 2 | 0 |
| Heat Treatment | W/SC:Work energy and power ,their units and applied problems. | 2 | 0 |
| Heat Treatment | TP:Forge punches,screw drivers,chisels, grind them to shape and heattreat torequirement,bending metals to angles, curves andtwisting ,Preparation of brackets | 20 | 0 |
| Heat Treatment | TP:Forge punches,screw drivers,chisels, grind them to shape and heattreat torequirement,bending metals to angles, curves andtwisting ,Preparation of brackets | 8 | 0 |
| Heat Treatment | Social Studies | 2 | 0 |
| Heat Treatment | Soft Skills:Active and passive voice | 2 | 0 |
| Sheet Metal | TT:Safety precaution to beobserved in a sheet metalwork-shop sheet and size.Commercial sizes and various types of metal sheets coated sheets and their uses as per ISI specifications. | 4 | 0 |
| Sheet Metal | ED:Pictorialdrawings isometric drawings of simplegeometrical solids. | 2 | 0 |
| Sheet Metal | W/SC:Work energy andpower ,their unitsand appliedproblems | 2 | 0 |
| Sheet Metal | TP:Marking of straight lines, circles,profiles and various geometrical shapes and cutting thesheets with snips.Marking out of simpledevelopmentmarking out for flaps for solderin gand sweating. | 20 | 0 |
| Sheet Metal | TP:Marking of straight lines, circles,profiles and various geometrical shapes and cutting thesheets with snips.Marking out of simpledevelopmentmarking out for flaps for solderin gand sweating. | 8 | 0 |
| Sheet Metal | Social Studies | 2 | 0 |
| Sheet Metal | Soft Skills:Writing and Speaking Test | 2 | 0 |
| Marking Tools | TT:Marking and measuring tools,Wing compass, Prick punch,tin man’s square tools, snips,types and uses. Tin man’shammers and mallets typesheetmetal tools, stakesbenchtypes , parts their uses.Soldering iron ,types,specifications, uses. Trammel,description ,parts, uses. Handgrooves specifications and uses. | 4 | 0 |
| Marking Tools | ED:Oblique projection ofsimple geometric-solids. | 2 | 0 |
| Marking Tools | W/SC:Percentage,changingp ercentage to decimal and fraction and vice versa.Applied problems. | 2 | 0 |
| Marking Tools | TP:Make variousjoints, wiring hemming, solderingand brazing fromlocked, groovedand knocked upsingle hem straight and curved edges from double hemming. Punchholes-using hollowand solid punches.Do lap and butt joints. | 20 | 0 |
| Marking Tools | TP:Make variousjoints, wiring hemming, solderingand brazing fromlocked, groovedand knocked upsingle hem straight and curved edges from double hemming. Punchholes-using hollowand solid punches.Do lap and butt joints. | 8 | 0 |
| Marking Tools | Social Studies | 2 | 0 |
| Marking Tools | Soft Skills:Writing and Speaking Test | 2 | 0 |
| Welding and Soldering | TT:Solders – composition ofvarious types of solders and their heating media ofsoldering iron . fluxes : types,selection and application –joints wiring various types ofmetals joints, their selection and application tolerance forvarious joints, their selection and application. | 4 | 0 |
| Welding and Soldering | ED:Oblique projection ofsimplegeometrical solids. | 2 | 0 |
| Welding and Soldering | W/SC:Problem on percentagerelated to trade | 2 | 0 |
| Welding and Soldering | TP:Bend sheet metalinto various curvature - formwired edges straight and curves fold sheet metal atan angle using stakes ,Bend sheet metal to variou scurvature make simple square –container with wired edge and fix handle | 20 | 0 |
| Welding and Soldering | TP:Bend sheet metalinto various curvature - formwired edges straight and curves fold sheet metal atan angle using stakes ,Bend sheet metal to variou scurvature make simple square –container with wired edge and fix handle | 8 | 0 |
| Welding and Soldering | Social Studies | 2 | 0 |
| Welding and Soldering | Soft Skills:Introducing oneself | 2 | 0 |
| Welding and Soldering | TT:Rivets – tin man’s rivets ,types, size, selection for various work.Riveting tool, dolly, snaps,descriptions and uses. Methodof riveting shearing machine description, parts and uses | 4 | 0 |
| Welding and Soldering | ED:Isometric drawing of simple machined and testing blocks | 2 | 0 |
| Welding and Soldering | W/SC:Different types of load, stress,strain modulus of elasticity | 2 | 0 |
| Welding and Soldering | TP:Make square tray with square soldered corner make funnel as perdevelopment andsolder joints. Make riveted left and beltjoint. | 20 | 0 |
| Welding and Soldering | TP:Make square tray with square soldered corner make funnel as perdevelopment andsolder joints. Make riveted left and beltjoint. | 8 | 0 |
| Welding and Soldering | Social Studies | 2 | 0 |
| Welding and Soldering | Soft Skills:Introducing oneself | 2 | 0 |
| Hanlding Welding Tools and Safety Precautions | TT:Safety – importance of safetyandgeneral precaution observed in a welding shop.precaution in electric andgas welding(before,during,after)introduction to safetyequipment and their uses | 4 | 0 |
| Hanlding Welding Tools and Safety Precautions | ED:Isometric drawing ofsimple machine and castingblock s | 2 | 0 |
| Hanlding Welding Tools and Safety Precautions | W/SC:Ultimate strengthdifferent types of stress, factor safety examples. | 2 | 0 |
| Hanlding Welding Tools and Safety Precautions | TP:Striking and maintaining arc,straight line head | 20 | 0 |
| Hanlding Welding Tools and Safety Precautions | TP:Striking and maintaining arc,straight line head | 8 | 0 |
| Hanlding Welding Tools and Safety Precautions | Social Studies | 2 | 0 |
| Hanlding Welding Tools and Safety Precautions | Soft Skills:7C's of communication | 2 | 0 |
| Hanlding Welding Tools and Safety Precautions | TT:Safety – importance of safetyandgeneral precaution observed in a welding shop.precaution in electric andgas welding(before,during,after)introduction to safety equipment and their uses | 4 | 0 |
| Hanlding Welding Tools and Safety Precautions | ED:Isometric drawing of simple machine and castingblock s | 2 | 0 |
| Hanlding Welding Tools and Safety Precautions | W/SC:Ultimate strength different types of stress, factor safety examples | 2 | 0 |
| Hanlding Welding Tools and Safety Precautions | TP:Striking and maintaining arc,straight line head | 20 | 0 |
| Hanlding Welding Tools and Safety Precautions | TP:Striking and maintaining arc,straight line head | 8 | 0 |
| Hanlding Welding Tools and Safety Precautions | Social Studies | 2 | 0 |
| Hanlding Welding Tools and Safety Precautions | Soft Skills:Self Awareness | 2 | 0 |
| Hanlding Welding Tools and Safety Precautions | TT:Hand tools:hammers,welding description, types and uses,machine and accessories welding transformer, welding generators, descriptionprinciple, method of operating | 8 | 0 |
| Hanlding Welding Tools and Safety Precautions | TP:Make squarae butt joint and ‘T’ fillet joint-gas and arc.do setting up of flames, fusion runs with and without filler rod,gas andarc. | 20 | 0 |
| Hanlding Welding Tools and Safety Precautions | TP:Make squarae butt joint and ‘T’ fillet joint-gas and arc.do setting up of flames, fusion runs with and without filler rod,gas andarc. | 8 | 0 |
| Hanlding Welding Tools and Safety Precautions | Social Studies | 2 | 0 |
| Hanlding Welding Tools and Safety Precautions | Soft Skills:Planning and Goal Setting | 2 | 0 |
| Hanlding Welding Tools and Safety Precautions | TT:H.P.welding equipment description, principle method of operating L.P welding equipment, description,principle, method of operating types: joints-Butt and fillet asper BIS specifications. | 4 | 0 |
| Hanlding Welding Tools and Safety Precautions | ED:Free handsketches of trader elated hand tools measuring tools. | 2 | 0 |
| Hanlding Welding Tools and Safety Precautions | W/SC:Ratio andproportion,Ratio, findingforms and ratioproportions,direct proportionand indirectproportion. | 2 | 0 |
| Hanlding Welding Tools and Safety Precautions | TP:Make square battjoint and ‘T’ filletjoint-gas and arc. | 20 | 0 |
| Hanlding Welding Tools and Safety Precautions | TP:Make square battjoint and ‘T’ filletjoint-gas and arc. | 8 | 0 |
| Hanlding Welding Tools and Safety Precautions | Social Studies | 2 | 0 |
| Hanlding Welding Tools and Safety Precautions | Soft Skills:Self Management | 2 | 0 |
| Cutting Machines and tools | TT:Oxygen cutting machinedescription, parts, uses,method of handling cuttingtorch-description, partsfunction and uses. Gases andgas cylinder description.Kinds main difference anduses | 4 | 0 |
| Cutting Machines and tools | ED:Free handsketches of traderelated handtools measuringtools. | 2 | 0 |
| Cutting Machines and tools | W/SC:Application ofratio andproportion torelated problems. | 2 | 0 |
| Cutting Machines and tools | TP:Do gas cutting. | 16 | 0 |
| Cutting Machines and tools | Social Studies | 2 | 0 |
| Cutting Machines and tools | Soft Skills:Self Management | 2 | 0 |
| Cutting Machines and tools | TT:Safety precautions to beobserved while working on alathe. Lathe specifications,and constructional features.Lathe main parts-descriptions,bed, head stock, carriage, tailstock, feeding and threadcutting mechanisms. Betweencentre work catch plate, dig,simple description of a facingand roughing tool and theirapplications. | 6 | 0 |
| Cutting Machines and tools | W/SC:SimpleMachines principlevelocityratio mechanical advantage,efficiency simpleproblems. | 2 | 0 |
| Cutting Machines and tools | TP:True job on fourjaw chuck usingknife tool face boththe ends forholding betweencentres. Usingroughing toolparallel turn=0.1mm. Measure thediameter usingoutside caliper andsteel rule. | 20 | 0 |
| Cutting Machines and tools | TP:True job on fourjaw chuck usingknife tool face boththe ends forholding betweencentres. Usingroughing toolparallel turn=0.1mm. Measure thediameter usingoutside caliper andsteel rule. | 8 | 0 |
| Cutting Machines and tools | Social Studies | 2 | 0 |
| Cutting Machines and tools | Soft Skills:Time Management | 2 | 0 |
| Cutting Machines and tools | TT:Lathe cutting tools Brier studyof the nomenclature of Lathecutting tools and necessity ofcorrect grinding, solid andtipped, throw away type toolscutting speed and feed andcomparison for H.H.S.,carbide tools. Use of coolantsand lubricants. | 4 | 0 |
| Cutting Machines and tools | ED:Machines basicprinciples,velocity, ratio,mechanicaladvantage,efficient, simpleproblems. | 2 | 0 |
| Cutting Machines and tools | W/SC:Simple machinesprinciple velocityratio mechanicaladvantage,efficiency.Sympleproblems. | 2 | 0 |
| Cutting Machines and tools | TP:Grind the facing,parting and formtools, plain turn,step turn, holdingjob in three jawchuck- Deburr,chamfer-cornerround the ends,Shoulder turn :square filletedbeveled under cutshoulders. | 20 | 0 |
| Cutting Machines and tools | TP:Grind the facing,parting and formtools, plain turn,step turn, holdingjob in three jawchuck- Deburr,chamfer-cornerround the ends,Shoulder turn :square filletedbeveled under cutshoulders. | 8 | 0 |
| Cutting Machines and tools | Social Studies | 2 | 0 |
| Cutting Machines and tools | Soft Skills:Time Management | 2 | 0 |
| Cutting Machines and tools | TT:Chucks and chucking theindependent four jaw chuck.Reversible features of jaws,the back plate, Method ofclearing the thread of thechuck-mounting anddismounting chucks chuckingtrue face plate drilling inmethod of holding drills in thetail stock, Boring tools andEnlargement of holes. | 4 | 0 |
| Cutting Machines and tools | ED:Orthographicdrawings,application ofboth the firstangle and thirdangle. Method inrepresenting thedrawing forsimple andcomplexmachine givenfor exerciseswith dimensions. | 2 | 0 |
| Cutting Machines and tools | W/SC:Algebraicsymbolsfundamentalalgebraoperations. Signand symbols usein algebracoefficient terms.And unliketerms. | 2 | 0 |
| Cutting Machines and tools | TP:Cut groves square,round ;V; groove,Make a mandrel turndiameter tosizes. Knurl the job | 20 | 0 |
| Cutting Machines and tools | TP:Cut groves square,round ;V; groove,Make a mandrel turndiameter tosizes. Knurl the job | 8 | 0 |
| Cutting Machines and tools | Social Studies | 2 | 0 |
| Cutting Machines and tools | Soft Skills:Game play | 2 | 0 |
| Turning | TT:General turning operationsparallel or straight, turning.Stepped turning grooving,shape of tools for the aboveoperations. Appropriatemethod of holding the tool ontool post or tool rest Knurlingtoolsdescription,grade,uses,speedand feed coolant for knurling. | 4 | 0 |
| Turning | ED:Orthographicdrawings,application ofboth the firstangle and thirdangle. Method inrepresenting thedrawing forsimple andcomplexmachine givenfor exerciseswith dimensions. | 2 | 0 |
| Turning | W/SC:Algebraicaddition,subtraction,multiplicationand division. | 2 | 0 |
| Turning | TP:Bore holes-spotface, pilot drill,enlarge hole, usingboring tools make abush. Step bore-cutrecess turn holediameter to sizes. | 20 | 0 |
| Turning | TP:Bore holes-spotface, pilot drill,enlarge hole, usingboring tools make abush. Step bore-cutrecess turn holediameter to sizes. | 8 | 0 |
| Turning | Social Studies | 2 | 0 |
| Turning | Soft Skills:Speaking and listening Activity | 2 | 0 |
| Turning | TT:Taper-definition use andmethod of expressing tapers.Standard tapers-tapercalculations. | 4 | 0 |
| Turning | ED:Orthographicdrawingsapplication ofboth the firstangle and thirdandgle. Methodin representingthe drawings forsimple andsimple andcomplexmachine blocksgiven forexercise withdimensions. | 2 | 0 |
| Turning | W/SC:Power andexponent Lawsof exponent | 2 | 0 |
| Turning | TP:Turn taper (internaland external.) Turntaper pins. Turnstandard tapers tosuit with Gauge. | 20 | 0 |
| Turning | TP:Turn taper (internaland external.) Turntaper pins. Turnstandard tapers tosuit with Gauge. | 8 | 0 |
| Turning | Social Studies | 2 | 0 |
| Turning | Soft Skills: Speaking and Listening Activity | 2 | 0 |
| Turning | TT:Screw thread definition-usesand application. Terminologyof screw threads, square wormbuttress (non standard-screwsthreads), Principle of cuttingscrew thread in centre latheprinciple of chasing screwsthread-use of centre gaugesetting tool for cutting internaland external thread cutting useof screw pitch gauge checkingthe screw thread. | 4 | 0 |
| Turning | ED:Orthographicdrawingsapplication ofboth the firstangle and thirdAngle. Methodin representingthe drawings forsimple andsimple andcomplexmachine blocksgiven forexercise withdimensions. | 2 | 0 |
| Turning | W/SC:Algebraicsimplificationproblems. | 2 | 0 |
| Turning | TP:Cut threads usingtaps and dies on latheby hand cut “V”thread-external.Prepare a nut andmatch with. Thebolt. | 20 | 0 |
| Turning | TP:Cut threads usingtaps and dies on latheby hand cut “V”thread-external.Prepare a nut andmatch with. Thebolt. | 8 | 0 |
| Turning | Social Studies | 2 | 0 |
| Turning | Soft Skills:Team Building | 2 | 0 |
| Drilling Materials | TT:Drill material types (Tapershank straight shank) partsand sizes Drill angle-cuttingangle for different materials,cutting speed feed. R.P.M fordifferent materials. | 4 | 0 |
| Drilling Materials | ED:Standard methodof sectioning asper IS : 696Exercises fordifferentsectional viewson the givenorthographicdrawing ofmachine parts,castings etc. | 2 | 0 |
| Drilling Materials | W/SC:Simple machineslike winch pulleyand compoundaxle e | 2 | 0 |
| Drilling Materials | TP:Mark off and drillthrough holes-drillon M.S. flat fileradius and profileto suit gauge. | 20 | 0 |
| Drilling Materials | TP:Mark off and drillthrough holes-drillon M.S. flat fileradius and profileto suit gauge. | 8 | 0 |
| Drilling Materials | Social Studies | 2 | 0 |
| Drilling Materials | Soft Skills:Team Building | 2 | 0 |
| Drilling Materials | TT:Droll troubles : causes adremedy. Equality of lips,correct clearance dead centrelangth of lips. Drill dinds:fractions metric, letters andnumbers, grinding of drill | 4 | 0 |
| Drilling Materials | ED:Standard methodof sectioning asper IS : 696Exercises fordifferentsectional viewson the givenorthographicdrawing ofmachine parts,castings etc | 2 | 0 |
| Drilling Materials | W/SC:Factors andequations”Algebraicformuls. | 2 | 0 |
| Drilling Materials | TP:Step fit angular fitfile and make anglesurfaces (Bevelgauge accuracy 1degree) makesimple open andsiding fits. | 20 | 0 |
| Drilling Materials | TP:Step fit angular fitfile and make anglesurfaces (Bevelgauge accuracy 1degree) makesimple open andsiding fits. | 8 | 0 |
| Drilling Materials | Social Studies | 2 | 0 |
| Drilling Materials | Soft Skills:Motivation and Inspiration | 2 | 0 |
| Grinding Wheel | TT:Grinding wheel : Abrasivegrift grade structure bondspecification us mounting anddressing Bench grinder partsand use-radius gauge filletgauge material construction,parts fraction and metricdifferent dimensions convexand concave uses care andmaintenance. | 6 | 0 |
| Grinding Wheel | W/SC:Factors anddifferent types offactorization. | 2 | 0 |
| Grinding Wheel | TP:Enlarge hole andincrease internaldia. File cylindricalsurfaces. Makeopen fitting ofcurved profiles. | 20 | 0 |
| Grinding Wheel | TP:Enlarge hole andincrease internaldia. File cylindricalsurfaces. Makeopen fitting ofcurved profiles. | 8 | 0 |
| Grinding Wheel | Social Studies | 2 | 0 |
| Grinding Wheel | Soft Skills:Motivation and Inspiration | 2 | 0 |
| Grinding Wheel | TT:Radius gauge feeler holegauge, and their uses. | 4 | 0 |
| Grinding Wheel | ED:Standard methodof sectioning asper IS : 696Exercises fordifferentsectional viewson the givenorthographicdrawing ofmachine parts,casting etc. | 2 | 0 |
| Grinding Wheel | W/SC:Equations simplesimultaneous. | 2 | 0 |
| Grinding Wheel | TP:Make the circles bybridging apreviously drilledhole. Test angularmatch up. | 20 | 0 |
| Grinding Wheel | TP:Make the circles bybridging apreviously drilledhole. Test angularmatch up. | 8 | 0 |
| Grinding Wheel | Social Studies | 2 | 0 |
| Grinding Wheel | Soft Skills: Public Speaking | 2 | 0 |
| Vernier Gauge | TT:Vernier height gauge :material construction, partsgraduations (English andMetric) uses care andmaintenance pig iron :manufacturing process (Blastfurnace) Types properties anduses. | 4 | 0 |
| Vernier Gauge | ED:InterconversionOf isometricoblique drawingsto orthographicdrawings andvice-versaRelatedproblems such a“V” blockoriented byvariousmachiningoperation etc. | 2 | 0 |
| Vernier Gauge | W/SC:Equations simplesimultaneous,quadratic. | 2 | 0 |
| Vernier Gauge | TP:Inside square fitmake combinedopen and sliding fitstraight sides :T: fit | 20 | 0 |
| Vernier Gauge | TP:Inside square fitmake combinedopen and sliding fitstraight sides :T: fit | 8 | 0 |
| Vernier Gauge | Social Studies | 2 | 0 |
| Vernier Gauge | Soft Skills:Public speaking | 2 | 0 |
| Cost Iron | TT:Cast iron : manufacturingprocess (cupola furnace) typesproperties and uses. Wroughtiron: manufacturing process(Pudding and Astor process )properties and uses. | 6 | 0 |
| Cost Iron | W/SC:Applicationconstruction andsolution ofproblemsBy equation. | 2 | 0 |
| Cost Iron | TP:File fit combinedopen angular andsliding sides. Fileinternal angles 30minutes accuracyopen angular fit. | 20 | 0 |
| Cost Iron | TP:File fit combinedopen angular andsliding sides. Fileinternal angles 30minutes accuracyopen angular fit. | 8 | 0 |
| Cost Iron | Social Studies | 2 | 0 |
| Cost Iron | Soft Skills:Situation play | 2 | 0 |
| Steel and Non-ferrous metals | TT:Steel : manufacturing processplain carbon steels typesproperties and uses. | 6 | 0 |
| Steel and Non-ferrous metals | W/SC:Atmosphericpressure pressurepressure andabsolute pressureand their units. | 2 | 0 |
| Steel and Non-ferrous metals | TP:Make sliding fitwith angles otherthan 90 sliding fitwith an angle. | 20 | 0 |
| Steel and Non-ferrous metals | TP:Make sliding fitwith angles otherthan 90 sliding fitwith an angle. | 8 | 0 |
| Steel and Non-ferrous metals | Social Studies | 2 | 0 |
| Steel and Non-ferrous metals | Soft Skills:Situation Play | 2 | 0 |
| Steel and Non-ferrous metals | TT:Non-ferrous metals (copper,Aluminum tin, lead, zinc.)properties and uses. | 6 | 0 |
| Steel and Non-ferrous metals | W/SC:Logarithms anduse of logarithmstables :Logarithms:logarithm andexponent. | 2 | 0 |
| Steel and Non-ferrous metals | TP:Make simplebracket by bendingand twistingnonferrous metsl.Drill small hole(2mm) Drill holeson sheet metal,bend sheet forround bracket. | 20 | 0 |
| Steel and Non-ferrous metals | TP:Make simplebracket by bendingand twistingnonferrous metsl.Drill small hole(2mm) Drill holeson sheet metal,bend sheet forround bracket. | 8 | 0 |
| Steel and Non-ferrous metals | Social Studies | 2 | 0 |
| Steel and Non-ferrous metals | Soft Skills:Ethics | 2 | 0 |
| Screw threads and Dies | TT:Screw threads : itsterminology parts, types, andtheir uses. Screw pitch gauge :material parts and uses , TapsBritish standard (B.S.W.,B.S.F., B.A and B.S.P) andmetric\BIS (course and fine)material parts (shank boadflute cutting edge) Method ofusing and use of calculatingtap hole sizes. Tap wrench :material parts types (solid andadjustable types) and theiruses removal of broken tap,studs (tap stud extractor). | 6 | 0 |
| Screw threads and Dies | W/SC:Use oflogarithms andanti-logarithmtable. | 2 | 0 |
| Screw threads and Dies | TP:Form internalthreads with taps toStandards size(through holes andblind holes) Drillthrough hole andtap drill blind holeand tap; preparestuds and bolt | 20 | 0 |
| Screw threads and Dies | TP:Form internalthreads with taps toStandards size(through holes andblind holes) Drillthrough hole andtap drill blind holeand tap; preparestuds and bolt | 8 | 0 |
| Screw threads and Dies | Social Studies | 2 | 0 |
| Screw threads and Dies | Soft Skills:Ethics | 2 | 0 |
| Screw threads and Dies | TT:Dies : British standard metricand BIS standard material,parts, types, Method of usingdies. Die stick: material partsand uses. | 6 | 0 |
| Screw threads and Dies | W/SC:Arithmeticaloperationsinvolvinglogarithms in thecomputations.44 | 2 | 0 |
| Screw threads and Dies | TP:From externalthreads with dies tostandard size.Prepare nuts andmatch with bolts | 20 | 0 |
| Screw threads and Dies | TP:From externalthreads with dies tostandard size.Prepare nuts andmatch with bolts | 8 | 0 |
| Screw threads and Dies | Social Studies | 2 | 0 |
| Screw threads and Dies | Soft Skills:Ethics | 2 | 0 |
| Scrapping | TT:Counter sink, counter bore andspot facing-tools andnomenclature, Reamermaterial types (Hand andmachine reamer) kinds partsand their uses determininghole size (or reaming )Reaming procedure Scrapersand their types, methods ofscraping. | 6 | 0 |
| Scrapping | W/SC:Problem relatedto be trade usinglogarithmtables.45 | 2 | 0 |
| Scrapping | TP:Counter sinkcounter bore andream split fit (threepiece fitting) | 20 | 0 |
| Scrapping | TP:Counter sinkcounter bore andream split fit (threepiece fitting) | 8 | 0 |
| Scrapping | Social Studies | 2 | 0 |
| Scrapping | Soft Skills:Ethics | 2 | 0 |
| Scrapping | TT:Scrapers and their types,methods of scraping. | 4 | 0 |
| Scrapping | ED:Surfacedevelopment ofsimplegeometricalsolids like cuberectangularblock cone,pyramid,cylinder prismetc. | 2 | 0 |
| Scrapping | W/SC:Problem relatedto be trade usinglogarithmtables.45 | 2 | 0 |
| Scrapping | TP:Filing and scrapingof bearing to closeprecision. | 20 | 0 |
| Scrapping | TP:Filing and scrapingof bearing to closeprecision. | 8 | 0 |
| Scrapping | Social Studies | 2 | 0 |
| Scrapping | Soft Skills: Ethics | 2 | 0 |
| Micrometer | TT:Vernier micrometer, material,parts graduation, use, care andmaintenance. | 4 | 0 |
| Micrometer | ED:Surfacedevelopment ofsimplegeometricalsolids like cuberectangularblock cone,pyramid,cylinder prismetc. | 2 | 0 |
| Micrometer | W/SC:Specific gravityprinciple ofArchimedes. | 2 | 0 |
| Micrometer | TP:File and fitcombined radiusand angular surface(accuracy =.5 mm.)angular and radiusfit. Locate accurateholes. MakeAccurate hole for studfit. | 20 | 0 |
| Micrometer | TP:File and fitcombined radiusand angular surface(accuracy =.5 mm.)angular and radiusfit. Locate accurateholes. MakeAccurate hole for studfit. | 8 | 0 |
| Micrometer | Social Studies | 2 | 0 |
| Micrometer | Soft Skills:Interpersonal skills | 2 | 0 |
| Micrometer | TT:Screw thread micrometer:construction, graduation anduse. | 4 | 0 |
| Micrometer | ED:Surfacedevelopment ofsimplegeometricalsolids like cuberectangularblock cone,pyramid,cylinder prismetc. | 2 | 0 |
| Micrometer | W/SC:Relation betweenspecific gravityand densitysimpleexperimentaldetermination. | 2 | 0 |
| Micrometer | TP:Make assemble fordovetail sliding fitsusing lower pinsand screw(o.04mm.) | 20 | 0 |
| Micrometer | TP:Make assemble fordovetail sliding fitsusing lower pinsand screw(o.04mm.) | 8 | 0 |
| Micrometer | Social Studies | 2 | 0 |
| Micrometer | Soft Skills:Interpersonal Skills | 2 | 0 |
| Dial Test Indicator | TT:Dial test indicator,construction, parts material,graduation, Method of use.Care and maintenance. | 4 | 0 |
| Dial Test Indicator | ED:Interetation ofsolids andconventionalapplication ofIntersectionalcurves ondrawing. | 2 | 0 |
| Dial Test Indicator | W/SC:Geometry:Fundamentalgeometricaldefinition anglesand properties ofangles, triangles,and properties oftriangles. | 2 | 0 |
| Dial Test Indicator | TP:Make sliding fitsassembly withparallel and angularmating surface.(+ 0.04mm) | 20 | 0 |
| Dial Test Indicator | TP:Make sliding fitsassembly withparallel and angularmating surface.(+ 0.04mm) | 8 | 0 |
| Dial Test Indicator | Social Studies | 2 | 0 |
| Dial Test Indicator | Soft Skills:Interpersonal Skills | 2 | 0 |
| P.M. Section and Revision | TT:Preventive maintenanceobjective and function of P.M.section inspection. Visual anddetailed lubrication surveysystem of symbol and colourcoating. | 4 | 0 |
| P.M. Section and Revision | ED:Interetation ofsolids andconventionalapplication ofIntersectionalcurves ondrawing. | 2 | 0 |
| P.M. Section and Revision | W/SC:Pythagorastheorem,properties ofsimilar triangles. | 2 | 0 |
| P.M. Section and Revision | TP:Practice on testingof machine tools and general shopmaintenance. | 20 | 0 |
| P.M. Section and Revision | TP:Practice on testingof machine tools and general shopmaintenance. | 8 | 0 |
| P.M. Section and Revision | Social Studies | 2 | 0 |
| P.M. Section and Revision | Soft Skills:Group discussions | 2 | 0 |
| P.M. Section and Revision | TT:Revision simple estimation of materials use of hand booksand reference table. | 8 | 0 |
| P.M. Section and Revision | ED:Solution ofNCVT test paper(preliminary)Revision. | 4 | 0 |
| P.M. Section and Revision | W/SC:Revision. | 4 | 0 |
| P.M. Section and Revision | TP:Simple repair work.Simple assemblymachine parts fromblue prints. | 20 | 0 |
| P.M. Section and Revision | TP:Simple repair work.Simple assemblymachine parts fromblue prints. | 20 | 0 |
| P.M. Section and Revision | TP:Simple repair work.Simple assemblymachine parts fromblue prints. | 16 | 0 |
| P.M. Section and Revision | Social Studies | 4 | 0 |
| P.M. Section and Revision | Soft Skills:Revision | 4 | 0 |
| Test | Test | 20 | 0 |
| Test | Test | 20 | 0 |
| Fitting materials | TT:Keys and keyways. Typesand their uses construction(shape). | 4 | 0 |
| Fitting materials | ED:Revision of firstyear topics. | 2 | 0 |
| Fitting materials | W/SC:Revision of 1styear course. | 2 | 0 |
| Fitting materials | TP:Prepare triangle,hexagon on ends ofa cylinder barprepare female endand fit. | 20 | 0 |
| Fitting materials | TP:Prepare triangle,hexagon on ends ofa cylinder barprepare female endand fit. | 8 | 0 |
| Fitting materials | Social Studies | 2 | 0 |
| Fitting materials | Soft Skills:Group discussion | 2 | 0 |
| Fitting materials | TT:Spring material types anduses. | 4 | 0 |
| Fitting materials | ED:Revision of firstyear topics | 2 | 0 |
| Fitting materials | W/SC:Revision of 1styear course | 2 | 0 |
| Fitting materials | TP:Make key andkeyways on theshaft and fit. ;V;grooves and slotson the cast ironblock | 20 | 0 |
| Fitting materials | TP:Make key andkeyways on theshaft and fit. ;V;grooves and slotson the cast ironblock | 8 | 0 |
| Fitting materials | Social Studies | 2 | 0 |
| Fitting materials | Soft Skills:Workplace and telephone Etiquettes | 2 | 0 |
| Fitting materials | TT:Bolts and Nuts: Material types(Hexagonal and square head)and their uses. | 4 | 0 |
| Fitting materials | ED:Screw threadtheir standardforms as per ISI,external andinternal thread,conventions onthe features fordrawing as perISI. | 4 | 0 |
| Fitting materials | W/SC:Rectangle,square, Rhombusparallelogramand theirproperties | 4 | 0 |
| Fitting materials | TP:Make riveted joints(lap and butt joints) | 20 | 0 |
| Fitting materials | TP:Make riveted joints(lap and butt joints) | 8 | 0 |
| Fitting materials | Social Studies | 2 | 0 |
| Fitting materials | Soft Skills:Telephone Etiquettes | 2 | 0 |
| Fitting materials | TT:Washers : Material, types(spring, tab plain washer andfiber washer) | 4 | 0 |
| Fitting materials | ED:Screw threadtheir standardforms as per ISI,external andinternal thread,conventions onthe features fordrawing as perISI. | 2 | 0 |
| Fitting materials | W/SC:Circle andproperties ofcircle : regularpolyons. | 2 | 0 |
| Fitting materials | TP:Drill on cylindricalsurface. | 20 | 0 |
| Fitting materials | TP:Drill on cylindricalsurface. | 8 | 0 |
| Fitting materials | Social Studies | 2 | 0 |
| Fitting materials | Soft Skills:Resume writing and Interview Skills | 2 | 0 |
| Fitting materials | TP:Scrap on fatSurfaces scrap oncurved surfaces andscrap surfaceparallels and test.Make and assemblesliding fits-plainsurfaces. | 20 | 0 |
| Fitting materials | TP:Scrap on fatSurfaces scrap oncurved surfaces andscrap surfaceparallels and test.Make and assemblesliding fits-plainsurfaces. | 16 | 0 |
| Fitting materials | Social Studies | 2 | 0 |
| Fitting materials | Soft Skills:Resume writing and Interview Skills | 2 | 0 |
| Fitting materials | TT:Dowel pins: materialconstruction types accuracyand uses. | 4 | 0 |
| Fitting materials | ED:Sketches forbolts, nuts,screws and otherscrewedmembers. | 2 | 0 |
| Fitting materials | W/SC:Heat andtemperaturethermos metricscales-theirconversions. | 2 | 0 |
| Fitting materials | TP:Make simple dowelPins fitting dowelpins and tap screwassemble | 20 | 0 |
| Fitting materials | TP:Make simple dowelPins fitting dowelpins and tap screwassemble | 8 | 0 |
| Fitting materials | Social Studies | 2 | 0 |
| Fitting materials | Soft Skills:Resume writing and interview skills | 2 | 0 |
| Fitting materials | TT:Screws : material, differenttypes (inch and metric) uses.. | 4 | 0 |
| Fitting materials | ED:Standard riverforms as per ISI | 2 | 0 |
| Fitting materials | W/SC:Temperaturemeasuringinstruments. | 2 | 0 |
| Fitting materials | TP:Assembly slidingfor using keys andsowel pin andscrew +0.02 mmplin surfac | 20 | 0 |
| Fitting materials | TP:Assembly slidingfor using keys andsowel pin andscrew +0.02 mmplin surfac | 8 | 0 |
| Fitting materials | Social Studies | 2 | 0 |
| Fitting materials | Soft Skills:Attending Interviews | 2 | 0 |
| Testing scraped surfaces | TT:Testing scraped surfaces: ordinary surfaces without amaster plate. | 4 | 0 |
| Testing scraped surfaces | ED:Standard rivetforms as per ISI | 2 | 0 |
| Testing scraped surfaces | W/SC:Specific heats ofsolids and liquids,quantity of heat. | 2 | 0 |
| Testing scraped surfaces | TP:Testing of slidingfitting job scrap ontwo flat surfaces andcurvedsurfaces. | 20 | 0 |
| Testing scraped surfaces | TP:Testing of slidingfitting job scrap ontwo flat surfaces andcurvedsurfaces. | 8 | 0 |
| Testing scraped surfaces | Social Studies | 2 | 0 |
| Testing scraped surfaces | Soft Skills: Attending Interviews | 2 | 0 |
| Special files | TT:Special files : types (Pillar,Dreadnought BarrowWarding) description. | 4 | 0 |
| Special files | ED:Riveted joint | 2 | 0 |
| Special files | W/SC:Heat loss andheat gain, withsimple problems. | 2 | 0 |
| Special files | TP:File and fit angularmating surfaceplain within anaccuracy of +0.02mm and angular+ 15 minutesangular fitting. | 20 | 0 |
| Special files | TP:File and fit angularmating surfaceplain within anaccuracy of +0.02mm and angular+ 15 minutesangular fitting. | 8 | 0 |
| Special files | Social Studies | 2 | 0 |
| Special files | Soft Skills:Stress Management | 2 | 0 |
| System of Drill Size | TT:System of drill size. Fractionalsize: number, latter andmetric. Templates and gauges.Introduction, necessity types.. | 4 | 0 |
| System of Drill Size | ED:Riveted jointsbutt. | 2 | 0 |
| System of Drill Size | W/SC:Mensuration :Plain fig urestriangles, square,rectangle,parallelogra | 2 | 0 |
| System of Drill Size | TP:Drill through andblind holes at anangle drill blindholes “Y” fitting | 20 | 0 |
| System of Drill Size | TP:Drill through andblind holes at anangle drill blindholes “Y” fitting | 8 | 0 |
| System of Drill Size | Social Studies | 2 | 0 |
| System of Drill Size | Soft Skills:Stress Management | 2 | 0 |
| Gauge | TT:Gauges: Introduction, types types-description and usesof gauge types (Feeler screw,pitch, radius, Wire gauge) | 4 | 0 |
| Gauge | ED:Sketches of keyscutter, and pinjoints. | 2 | 0 |
| Gauge | W/SC:Plain figures.Trapeziumregular polygons,circle hollowCircles. | 2 | 0 |
| Gauge | TP:Dovetailed fittingradius fitting | 20 | 0 |
| Gauge | TP:Dovetailed fittingradius fitting | 8 | 0 |
| Gauge | Social Studies | 2 | 0 |
| Gauge | Soft Skills:Stress Management | 2 | 0 |
| Gauge | TT:Description and use.Limit gauge: Ring gauge, snapgauge, plug gauge, descriptionand use. | 4 | 0 |
| Gauge | ED:Sketches of keyscutter, and pinjoints | 2 | 0 |
| Gauge | W/SC:Plain figuresandsector of circleellipse, fillets. | 2 | 0 |
| Gauge | TP:Precision drillingreaming andlapping.Test job | 20 | 0 |
| Gauge | TP:Precision drillingreaming andlapping.Test job | 8 | 0 |
| Gauge | Social Studies | 2 | 0 |
| Gauge | Soft Skills:Telecommunication skills | 2 | 0 |
| Gauge | TT:Slip gauge : Necessity ofaccuracy set of block (Englishand Metric) Details of slipgauge. Mets 46:103:112 .Wrining and building up ofslip gauge and care andmaintenance. Application ofslip gauges for measuring,sine bar-principle, applicationand specification. | 8 | 0 |
| Gauge | TP:File and fitcombined fit withstraight angularsurface +0.02mm,hexagonal fitting | 20 | 0 |
| Gauge | TP:File and fitcombined fit withstraight angularsurface +0.02mm,hexagonal fitting | 8 | 0 |
| Gauge | Social Studies | 2 | 0 |
| Gauge | Soft Skills: Interview Skills | 2 | 0 |
| Locking Device | TT:Locking device : Nuts types(lock nut castle nut, slottednuts, swam nut, grooved nut).Description and use. | 6 | 0 |
| Locking Device | W/SC:Solid figures :Frustum of acone, spheresphericalsegment. | 2 | 0 |
| Locking Device | TP:Drill and reamsmall dia holes toaccuracy correctlocation for fitting.Make male andfemale fitting parts drilland ream holesnot less that 12.7mm. | 20 | 0 |
| Locking Device | TP:Drill and reamsmall dia holes toaccuracy correctlocation for fitting.Make male andfemale fitting parts drilland ream holesnot less that 12.7mm. | 8 | 0 |
| Locking Device | Social Studies | 2 | 0 |
| Locking Device | Soft Skills:Attending Interviews | 2 | 0 |
| Lapping and Horning | TT:Lapping: Application oflapping material for lappingtools, lapping abrasivescharging of lapping tool. Surface finish importanceequipment for testing- termsrelation to surface finish.Equipment for testing surfacesquality dimensional tolerancesof surface finish. | 4 | 0 |
| Lapping and Horning | ED:Concept ofpreparation ofassemblydrawing anddetailing. Simpleassemblies andtheir details oftrade relatedtools\job\exercises with thedimensions fromthe given sampleof models. Toolpost for the lathewith washer andscrew. | 2 | 0 |
| Lapping and Horning | W/SC:Material weightand costproblems relatedto trade. | 2 | 0 |
| Lapping and Horning | TP:Sliding fittingDiamond fittng,Lapping flatsurfaces usinglapping plate. | 20 | 0 |
| Lapping and Horning | TP:Sliding fittingDiamond fittng,Lapping flatsurfaces usinglapping plate. | 8 | 0 |
| Lapping and Horning | Social Studies | 2 | 0 |
| Lapping and Horning | Soft Skills | 2 | 0 |
| Lapping and Horning | TT:Honing;Application of honing material for honing toolsshapes, grades-honingabrasives. Frosting its am andthe methods of performance. | 4 | 0 |
| Lapping and Horning | ED:Concept ofpreparation ofassemblydrawing anddetailing. Simpleassemblies andtheir details oftrade relatedtools\job\exercises with thedimensions fromthe given sampleof models. Toolpost for the lathewith washer andscrew | 2 | 0 |
| Lapping and Horning | W/SC:Trigonometry:trigonometricalratios use oftrigonometricaltable. | 2 | 0 |
| Lapping and Horning | TP:Stepped keyedfitting test job.Lapping holes andcylindricalsurfaces. | 20 | 0 |
| Lapping and Horning | TP:Stepped keyedfitting test job.Lapping holes andcylindricalsurfaces. | 8 | 0 |
| Lapping and Horning | Social Studies | 2 | 0 |
| Lapping and Horning | Soft Skills | 2 | 0 |
| Interchangeability | TT:Interchangeability : Necessityin Engg. Field definition BISDefinition, types of limitterminology of limits and fitsbasic size, actual size,deviation high and lowlimitzero ine, tolerance zone. | 4 | 0 |
| Interchangeability | ED:Details andassembly of vee blockswithclamps. | 2 | 0 |
| Interchangeability | W/SC:Area of triangleby trigonometry. | 2 | 0 |
| Interchangeability | TP:Make a snap gauge+ 0.02 mm. | 20 | 0 |
| Interchangeability | TP:Make a snap gauge+ 0.02 mm. | 8 | 0 |
| Interchangeability | Social Studies | 2 | 0 |
| Interchangeability | Soft Skills | 2 | 0 |
| Interchangeability | TT:Different standard systems offits and limits. Britishstandard system. BIS system.Method of expressingtolerance as per BIS. | 4 | 0 |
| Interchangeability | ED:Details assemblyof vee blockwith clamps. | 2 | 0 |
| Interchangeability | W/SC:Finding heightand distance bytrigonometry. | 2 | 0 |
| Interchangeability | TP:Scrape angularmating surface,scrap on internalsurface. | 20 | 0 |
| Interchangeability | TP:Scrape angularmating surface,scrap on internalsurface. | 8 | 0 |
| Interchangeability | Social Studies | 2 | 0 |
| Interchangeability | Soft Skills | 2 | 0 |
| Fits | TT:Fits: Definition, types,description of each withsketch. | 4 | 0 |
| Fits | ED:Details ofassembly ofshaft and pulley | 2 | 0 |
| Fits | W/SC:Application oftrigonometry toshop problems. | 2 | 0 |
| Fits | TP:Practice in dovetailfitting assemblyand dowel pinsIndustrial visit | 20 | 0 |
| Fits | TP:Practice in dovetailfitting assemblyand dowel pinsIndustrial visit | 8 | 0 |
| Fits | Social Studies | 2 | 0 |
| Fits | Soft Skills | 2 | 0 |
| Manufacturing | TT:Manufacture : the name andtypes of gauge commonlyused in gauging finishedproduct Method of selectiveassembly “Go” system ofgauges, hole plug basis ofstandardization. | 4 | 0 |
| Manufacturing | ED:Details ofassembly shaftand pulley. | 2 | 0 |
| Manufacturing | TP:Preparation of gapgauges. | 20 | 0 |
| Manufacturing | TP:Preparation of gapgauges. | 8 | 0 |
| Manufacturing | Social Studies | 2 | 0 |
| Manufacturing | Soft Skills | 2 | 0 |
| Manufacturing | TT:Bearing introduction.Classification (journal andThrust Description of eachball bearing: sigle row doublerow, description of each,advantages of double row. | 4 | 0 |
| Manufacturing | ED:Details ofassembly ofbush bearing. | 2 | 0 |
| Manufacturing | W/SC:Tringle of forces,parallelogram offorces. | 2 | 0 |
| Manufacturing | TP:Dovetail andDowel pinassembly scrapecylindrical bore. | 20 | 0 |
| Manufacturing | TP:Dovetail andDowel pinassembly scrapecylindrical bore. | 8 | 0 |
| Manufacturing | Social Studies | 2 | 0 |
| Manufacturing | Soft Skills | 2 | 0 |
| Manufacturing | TT:Roller and needle bearings:Types of roller bearingDescription and use of eachMethod of fitting bal androller bearings. | 4 | 0 |
| Manufacturing | ED:Details ofassembly bushbearing. | 2 | 0 |
| Manufacturing | W/SC:Composition andresolution offorces. | 2 | 0 |
| Manufacturing | TP:Scrap cylindricalbore and to make afit make a cotter jibassembly. | 20 | 0 |
| Manufacturing | TP:Scrap cylindricalbore and to make afit make a cotter jibassembly. | 8 | 0 |
| Manufacturing | Social Studies | 2 | 0 |
| Manufacturing | Soft Skills | 2 | 0 |
| Manufacturing | TT:Bearing metals types,composition and lubricantspupose of using differenttypes description and uses ofeach type. | 4 | 0 |
| Manufacturing | ED:Details ofassembly bushbearing | 4 | 0 |
| Manufacturing | W/SC:Composition andresolution offorces. | 2 | 0 |
| Manufacturing | TP:Scrap cylindricaltaper bore checktaper angle (flat)with sine bar. | 20 | 0 |
| Manufacturing | TP:Scrap cylindricaltaper bore checktaper angle (flat)with sine bar. | 8 | 0 |
| Manufacturing | Social Studies | 2 | 0 |
| Manufacturing | Soft Skills | 2 | 0 |
| Manufacturing | TT:Synthetic materials forbearing: The plastic laminateand materials, their propertiesand uses in bearings such asphonolic pejlon polymide(nylon) | 4 | 0 |
| Manufacturing | ED:Details ofassembly bushbearing | 2 | 0 |
| Manufacturing | W/SC:Composition andresolution offorces | 2 | 0 |
| Manufacturing | TP:Scrap cylindricaltaper bore checktaper angle (flat)with sine bar | 20 | 0 |
| Manufacturing | TP:Scrap cylindricaltaper bore checktaper angle (flat)with sine bar | 8 | 0 |
| Manufacturing | Social Studies | 2 | 0 |
| Manufacturing | Soft Skills | 2 | 0 |
| Manufacturing | TT:Hardening and temperingpurpose of each method,tempering colour chart. | 4 | 0 |
| Manufacturing | ED:Details andassembly of asimple handvice. | 2 | 0 |
| Manufacturing | W/SC:Moments offorce couples. | 2 | 0 |
| Manufacturing | TP:File and fit straightand angularsurfaces internally | 20 | 0 |
| Manufacturing | TP:File and fit straightand angularsurfaces internally | 8 | 0 |
| Manufacturing | Social Studies | 2 | 0 |
| Manufacturing | Soft Skills | 2 | 0 |
| Manufacturing | TT:Annealing and normalizingpurpose of each method | 4 | 0 |
| Manufacturing | ED:Details andassembly of asimple handvice | 2 | 0 |
| Manufacturing | W/SC:Simple problemson straight andbel crankedlaver. | 2 | 0 |
| Manufacturing | TP:Heat treatment oftools. | 20 | 0 |
| Manufacturing | TP:Heat treatment oftools. | 8 | 0 |
| Manufacturing | Social Studies | 2 | 0 |
| Manufacturing | Soft Skills | 2 | 0 |
| Manufacturing | TT:Case hardening and carburizingand its methods process ofcarburizing (solid liquid andgas) | 4 | 0 |
| Manufacturing | ED:Details andassembly ofsimple hand vice | 2 | 0 |
| Manufacturing | W/SC:Centre of gravity,simpleexperimentaldeterminationstable unstable andneutralEquilibrium simpleexplanation | 2 | 0 |
| Manufacturing | TP:Flaring of pipesAnd pipe joints-heattreatment of coldchisels. | 20 | 0 |
| Manufacturing | TP:Flaring of pipesAnd pipe joints-heattreatment of coldchisels. | 8 | 0 |
| Manufacturing | Social Studies | 2 | 0 |
| Manufacturing | Soft Skills | 2 | 0 |
| Soldering | TT:Solder and solderingintroduction types of solderand Flux. Method of solderinghard solder introduction typesand method brazing. | 4 | 0 |
| Soldering | ED:Details andassembly ofsimple hand vice | 2 | 0 |
| Soldering | W/SC::Centre of gravity,simpleexperimentaldeterminationstable unstable andneutralEquilibrium simpleexplanation. | 2 | 0 |
| Soldering | TP:“H” fittingexercises onlapping of gauges(hand lapping only) | 20 | 0 |
| Soldering | TP:“H” fittingexercises onlapping of gauges(hand lapping only) | 8 | 0 |
| Soldering | Social Studies | 2 | 0 |
| Soldering | Soft Skills | 2 | 0 |
| Drilling Jigs | TT:Production of gaugestemplates and jigs. The objectof importance for preparinginterchangeable components. | 4 | 0 |
| Drilling Jigs | ED:Details andassembly ofsimple hand vice | 2 | 0 |
| Drilling Jigs | W/SC:Friction coefficient offriction | 2 | 0 |
| Drilling Jigs | TP:Hand ream and fittaper pin drillingand reaming hole incorrect lo9cation,fitting dowel pinsstud, and bolts. | 20 | 0 |
| Drilling Jigs | TP:Hand ream and fittaper pin drillingand reaming hole incorrect lo9cation,fitting dowel pinsstud, and bolts. | 8 | 0 |
| Drilling Jigs | Social Studies | 2 | 0 |
| Drilling Jigs | Soft Skills | 2 | 0 |
| Drilling Jigs | TT:Drilling jig constructionalfeatures, types and use | 4 | 0 |
| Drilling Jigs | ED:Blue printReading simpleexercises relatedto missing lines. | 2 | 0 |
| Drilling Jigs | W/SC:Simple problemrelated toFrication. | 2 | 0 |
| Drilling Jigs | TP:Simple jigs andfixtures for drilling. | 20 | 0 |
| Drilling Jigs | TP:Simple jigs andfixtures for drilling. | 8 | 0 |
| Drilling Jigs | Social Studies | 2 | 0 |
| Drilling Jigs | Soft Skills | 2 | 0 |
| Fitting | TT:Fixtures-construction featurestypes and uses. | 4 | 0 |
| Fitting | ED:Blue printreading. Simpleexercises relatedto missing lines. | 2 | 0 |
| Fitting | W/SC:Magneticsubstancesnatural andartificialmagnets. | 2 | 0 |
| Fitting | TP:Prepare a “V”block and clamp. | 20 | 0 |
| Fitting | TP:Prepare a “V”block and clamp. | 8 | 0 |
| Fitting | Social Studies | 2 | 0 |
| Fitting | Soft Skills | 2 | 0 |
| Fitting | TT:Revision. | 4 | 0 |
| Fitting | ED:Blue printreading simpleexercises relatedto missingviews. | 2 | 0 |
| Fitting | W/SC:Method ofmagnetization.Use of magnets | 2 | 0 |
| Fitting | TP:Marking out as perblue print drillingstraight and curvefiling threadingwith die cutting soltcutting internalthreads with tapsmaking andadjustable spanner | 20 | 0 |
| Fitting | TP:Marking out as perblue print drillingstraight and curvefiling threadingwith die cutting soltcutting internalthreads with tapsmaking andadjustable spanner | 8 | 0 |
| Fitting | Social Studies | 2 | 0 |
| Fitting | Soft Skills | 2 | 0 |
| Fitting | TT:Pipes and pipe fittingcommonly used pipes. Pipesbending fixture pipe threadsstd. pipe threads die and tappipe vices | 4 | 0 |
| Fitting | ED:Blue printreading simpleexercises relatedto missingviews. | 2 | 0 |
| Fitting | W/SC:Electricity and itsuses electriccurrent positiveand negativeterminals.8 | 2 | 0 |
| Fitting | TP:Cutting andThreading of pipelength Fitting ofpipes as per sketchconditions used forpipe work to befollowed. Bendingof pipes cold andhot | 20 | 0 |
| Fitting | TP:Cutting andThreading of pipelength Fitting ofpipes as per sketchconditions used forpipe work to befollowed. Bendingof pipes cold andhot | 8 | 0 |
| Fitting | Social Studies | 2 | 0 |
| Fitting | Soft Skills | 2 | 0 |
| Revision | TT: Revision | 4 | 0 |
| Revision | ED:Revision | 2 | 0 |
| Revision | W/SC:Revision | 2 | 0 |
| Revision | TP:Revision | 20 | 0 |
| Revision | TP:Revision | 8 | 0 |
| Revision | Social Studies | 2 | 0 |
| Revision | Soft Skills | 2 | 0 |
| Fire Extinguishers | TT:Fire precautions causes andtypes of fires precautionsagainst out break of fire. Fire extinguishers types and uses. | 4 | 0 |
| Fire Extinguishers | ED:Simple exercisesrelating tomissingsymbo | 2 | 0 |
| Fire Extinguishers | W/SC:Simple electriccircuits simplecalculations. | 2 | 0 |
| Fire Extinguishers | TP:Practice in handlingfire extinguishersof different typesrefilling ofextinguishers. | 2 | 0 |
| Fire Extinguishers | Social Studies | 2 | 0 |
| Fire Extinguishers | Soft Skills | 2 | 0 |
| Aluminum and Alloys | TT:Working material withfinished surface as aluminum,duralumin stainless steel, theimportance of keeping thework free from scratdes or rustand corrosion. The variouscoatings used to protectmetals, protection coat by heatand elecetrical deposittreatments.- Treatments and provide aplasing finish as chromiumsilver plating and nickelplating and galvanizing. | 4 | 0 |
| Aluminum and Alloys | ED:Simple exercisesrelated to missingsection. | 2 | 0 |
| Aluminum and Alloys | W/SC:Ohm”s Lawsimplecalculation,electricalinsulatingmaterials. | 2 | 0 |
| Aluminum and Alloys | TP:Marking detailinclude male andfemale screwcutting male andfemale fitting parts.Making andtempering | 20 | 0 |
| Aluminum and Alloys | TP:Marking detailinclude male andfemale screwcutting male andfemale fitting parts.Making andtempering | 8 | 0 |
| Aluminum and Alloys | Social Studies | 2 | 0 |
| Aluminum and Alloys | Soft Skills | 2 | 0 |
| Aluminum and Alloys | TT:Aluminum and its alloys Used advantages and disadvantage: weight and strengths compared with steel. | 4 | 0 |
| Aluminum and Alloys | ED:Simple exercises related to missing section. | 2 | 0 |
| Aluminum and Alloys | W/SC:Graphs: Abscissa and ordinates,graphs of straight line, related to two sets quantitativenesses. | 2 | 0 |
| Aluminum and Alloys | TP:Exercise unfinished material as Aluminum outputting to size drilling etc. without damage to surface of finished articles. | 20 | 0 |
| Aluminum and Alloys | TP:Exercise unfinished material as Aluminum outputting to size drilling etc. without damage to surface of finished articles. | 8 | 0 |
| Aluminum and Alloys | Social Studies | 2 | 0 |
| Aluminum and Alloys | Soft Skills | 2 | 0 |
| Non-ferrous metals | TT:Tapers on deys and cotters permissible by various standards. Discuss non-ferrous metals as brass, phosphor bronze, gun metal, copper,Aluminum etc. purposes-surface wearing properties of bronze and brass. | 4 | 0 |
| Non-ferrous metals | ED:Simplehearted tridimensionality. | 2 | 0 |
| Non-ferrous metals | W/SC:Abscissa and ordinates,graphs of straight line, related to two sets quantitativenesses. | 2 | 0 |
| Non-ferrous metals | TP:Making out for angular outlines filing and fitting the inserts into gaps. Making pleasing drilling jig Marking out-filing to line drilling an drapping brass and copper jobs.TP:Making out for angular outlines filing and fitting the inserts into gaps. Making pleasing drilling jig Marking out-filing to line drilling an drapping brass and copper jobs. | 20 | 0 |
| Non-ferrous metals | TP:Making out for angular outlines filing and fitting the inserts into gaps. Making pleasing drilling jig Marking out-filing to line drilling an drapping brass and copper jobs. | 8 | 0 |
| Non-ferrous metals | Social Studies | 2 | 0 |
| Non-ferrous metals | Soft Skills | 2 | 0 |
| Power Transmission Elements | TT:Power transmission elements.The object of belts-their size sand specifications materials of which the belts are Made selection of the type of belts with the consideration of weather load and Tension methods of joining leather belts.Vee belts and their advantage sand disadvantages Use commercial belts dressing Andre creep and slipping calculations. | 4 | 0 |
| Power Transmission Elements | ED:Simple exercise related to missing dimensions | 2 | 0 |
| Power Transmission Elements | W/SC:Further practice logarithm. | 2 | 0 |
| Power Transmission Elements | TP:Complete exercises covering the assembly of parts working to detail and arrangement Drawings.Dismantling and mounting of pulleys. Making replacing damaged gears keys.Repairing damaged keys. Repairing damaged gears and mounting. Repairand replacement of belts. Industrial visits. | 20 | 0 |
| Power Transmission Elements | TP:Complete exercises covering the assembly of parts working to detail and arrangement Drawings.Dismantling and mounting of pulleys. Making replacing damaged gears keys.Repairing damaged keys. Repairing damaged gears and mounting. Repairand replacement of belts. Industrial visits. | 8 | 0 |
| Power Transmission Elements | Social Studies | 2 | 0 |
| Power Transmission Elements | Soft Skills | 2 | 0 |
| Power Transmission Elements | TT:Power transmission coupling types flange coupling Hooks coupling universal coupling and their different uses. | 4 | 0 |
| Power Transmission Elements | W/SC:Mechanical properties of metals. | 2 | 0 |
| Power Transmission Elements | TP:Complete exercises covering the assembly of parts working to detail sand arrangements drawings.Dismantling and mounting of pulleys. Making replacing | 20 | 0 |
| Power Transmission Elements | TP:Complete exercises covering the assembly of parts working to detail sand arrangements drawings.Dismantling and mounting of pulleys. Making replacing | 8 | 0 |
| Power Transmission Elements | Social Studies | 2 | 0 |
| Power Transmission Elements | Soft Skills | 2 | 0 |
| Power Transmission Elements | TT:Pulley types solic, split and V belt pulleys standard calculation for determining size crowing of pulleys width of faces loose and fast pulleys jockey pulley types of drives operand cross belt drives.The geometrical explanation of the belt drivers at and angle | 4 | 0 |
| Power Transmission Elements | ED | 2 | 0 |
| Power Transmission Elements | W/SC | 2 | 0 |
| Power Transmission Elements | TP:More difficult working marking out including tangents templates involving us of Vernier protractor. | 20 | 0 |
| Power Transmission Elements | TP:More difficult working marking out including tangents templates involving us of Vernier protractor. | 8 | 0 |
| Power Transmission Elements | Social Studies | 2 | 0 |
| Power Transmission Elements | Soft Skills | 2 | 0 |
| Power Transmission Elements | TT:Power transmission by gears,most common form spur gear,set names of some essential parts of the set The pitch circles Diametral pitch velocity ratio of a gear set Helical gear,herring bone gears, livebearing spiral bevel gearing hypoid gearing pinion an drack, worm gearing, velocity ratio of worm gearing Repair to gear teeth by building pand dovetail method. | 4 | 0 |
| Power Transmission Elements | ED:Solution offence test. | 2 | 0 |
| Power Transmission Elements | W/SC:Heat treatment of steel hardening annealing,tempering,normal sing, casehardening standard and measurement. | 2 | 0 |
| Power Transmission Elements | TP:Fitting of dovetail slides. | 20 | 0 |
| Power Transmission Elements | TP:Fitting of dovetail slides. | 8 | 0 |
| Power Transmission Elements | Social Studies | 2 | 0 |
| Power Transmission Elements | Soft Skills | 2 | 0 |
| Method of Fixing | TT:Method of fixing geared wheels for various purpose drives. General cause of the wear and tear of the toothed wheels and their remedies method of fitting spiral gears helical gears bevel gears gormand worm wheels irrelation to required drive.Care and maintenance of gears. | 4 | 0 |
| Method of Fixing | ED:Solution offence test papers. | 2 | 0 |
| Method of Fixing | W/SC:Heat treatment of steel hardening annealing,tempering,normalizing, casehardening standard admeasurement. | 2 | 0 |
| Method of Fixing | TP:Male and female dovetail fitting repairs to geared teeth. Repair of broken gear toothy stud. Repair broker gear teeth by dovetail. | 20 | 0 |
| Method of Fixing | TP:Male and female dovetail fitting repairs to geared teeth. Repair of broken gear toothy stud. Repair broker gear teeth by dovetail. | 8 | 0 |
| Method of Fixing | Social Studies | 2 | 0 |
| Method of Fixing | Soft Skills | 2 | 0 |
| Friction and Lubricants | TT:Friction and lubricants.How lubrication is done. Agood lubricant, viscosity of the lubricant. Main property of lubricant. How a film of oil disformed in journal. Bearings method of lubrication gravity feed, force (pressure) feed,splash lubrication. Cutting lubricants and coolants:So lube oil soaps suds paraffin soda water common lubrication | 4 | 0 |
| Friction and Lubricants | ED:Solution offence test papers. | 2 | 0 |
| Friction and Lubricants | W/SC:Transmission power by belt pulley and gear drive. | 2 | 0 |
| Friction and Lubricants | TP:Marking out on the round sections for geometrical shaped fittings. Finishing and fitting to size,checking up the faces for universality. | 20 | 0 |
| Friction and Lubricants | TP:Marking out on the round sections for geometrical shaped fittings. Finishing and fitting to size,checking up the faces for universality. | 8 | 0 |
| Friction and Lubricants | Social Studies | 2 | 0 |
| Friction and Lubricants | Soft Skills | 2 | 0 |
| Friction and Lubricants | TT:Chains, wire ropes and clutches for power transmission. Their types befriend description. | 4 | 0 |
| Friction and Lubricants | ED:Solution offence test papers. | 2 | 0 |
| Friction and Lubricants | W/SC:Transmission of power by belt pulley and gear drive. | 2 | 0 |
| Friction and Lubricants | TP:Shaping parallel block and W block. | 20 | 0 |
| Friction and Lubricants | TP:Shaping parallel block and W block. | 8 | 0 |
| Friction and Lubricants | Social Studies | 2 | 0 |
| Friction and Lubricants | Soft Skills | 2 | 0 |
| Riveting and Drilling | TT:Discuss the various rivets shape and from of heads riveting tools for drawing up the importance of correct head size. The spacing of rivets.Flash riveting, use of correct tools compare hot and cold riveting. | 4 | 0 |
| Riveting and Drilling | ED:Revision | 2 | 0 |
| Riveting and Drilling | W/SC:Transmission of power by belt pulley and gear drive | 2 | 0 |
| Riveting and Drilling | TP:Drilling for riveting. Riveting with as many types of rivet as available use of counter lunkhead rivets use of counter bore tool toft cheese deadbolts. Use of po privets and gun. | 20 | 0 |
| Riveting and Drilling | TP:Drilling for riveting. Riveting with as many types of rivet as available use of counter lunkhead rivets use of counter bore tool toft cheese deadbolts. Use of po privets and gun. | 8 | 0 |
| Riveting and Drilling | Social Studies | 2 | 0 |
| Riveting and Drilling | Soft Skills | 2 | 0 |
| Overhaul of Machinery and Engineering Equipment | TT:Installation, maintenance and overhaul of machinery and engineering equipment and alignment of machines. | 4 | 0 |
| Overhaul of Machinery and Engineering Equipment | ED:Revision | 2 | 0 |
| Overhaul of Machinery and Engineering Equipment | W/SC:Solution offence papers. | 2 | 0 |
| Overhaul of Machinery and Engineering Equipment | TP:Dismantling removal and reassemble of simple machine tool. Dismantling and assemble of pillar type drilling machine. | 20 | 0 |
| Overhaul of Machinery and Engineering Equipment | TP:Dismantling removal and reassemble of simple machine tool. Dismantling and assemble of pillar type drilling machine. | 8 | 0 |
| Overhaul of Machinery and Engineering Equipment | Social Studies | 2 | 0 |
| Overhaul of Machinery and Engineering Equipment | Soft Skills | 2 | 0 |
| Overhaul of Machinery and Engineering Equipment | TT:Clutch: Type positive clutch(straight tooth types, angular tooth type) friction type (flatland conical type) | 4 | 0 |
| Overhaul of Machinery and Engineering Equipment | ED:Revision | 2 | 0 |
| Overhaul of Machinery and Engineering Equipment | W/SC:Solution offence papers | 2 | 0 |
| Overhaul of Machinery and Engineering Equipment | TP:Milling Plain, slotand angular cutting. | 20 | 0 |
| Overhaul of Machinery and Engineering Equipment | TP:Milling Plain, slotand angular cutting. | 8 | 0 |
| Overhaul of Machinery and Engineering Equipment | Social Studies | 2 | 0 |
| Overhaul of Machinery and Engineering Equipment | Soft Skills | 2 | 0 |
| Overhaul of Machinery and Engineering Equipment | TT:Washers Types and calculation of washer sizes.The making of joints and fitting packing The use of lifting appliances, extractor presses and their use. Practical method of obtaining mechanical advantage. The slings and handling of heavy machinery.Special precautions in the removal and replacement of heavy parts. | 4 | 0 |
| Overhaul of Machinery and Engineering Equipment | ED:Revision | 2 | 0 |
| Overhaul of Machinery and Engineering Equipment | W/SC:Solution offence papers | 2 | 0 |
| Overhaul of Machinery and Engineering Equipment | TP:Grinding Surfaceand circular. | 20 | 0 |
| Overhaul of Machinery and Engineering Equipment | TP:Grinding Surfaceand circular. | 8 | 0 |
| Overhaul of Machinery and Engineering Equipment | Social Studies | 2 | 0 |
| Overhaul of Machinery and Engineering Equipment | Soft Skills | 2 | 0 |
| Overhaul of Machinery and Engineering Equipment | TT:Foundation bolt: types (rag,lewis cotter bolt) description of each erection tools, pulley block, crow bar, spiritlevel,plumb bob 2+4, wire rope, manual rope, wooden block. | 4 | 0 |
| Overhaul of Machinery and Engineering Equipment | ED:Revision | 2 | 0 |
| Overhaul of Machinery and Engineering Equipment | W/SC:Revision | 2 | 0 |
| Overhaul of Machinery and Engineering Equipment | TP:Simple repair of machinery making of packings gaskets use of hollow panties,extractor drifts various types of hammers and spanners, etc.practicing making various knots correct loading and safe removal of parts. Erect sample machines. | 20 | 0 |
| Overhaul of Machinery and Engineering Equipment | TP:Simple repair of machinery making of packings gaskets use of hollow panties,extractor drifts various types of hammers and spanners, etc.practicing making various knots correct loading and safe removal of parts. Erect sample machines. | 8 | 0 |
| Overhaul of Machinery and Engineering Equipment | Social Studies | 2 | 0 |
| Overhaul of Machinery and Engineering Equipment | Soft Skills | 2 | 0 |